Pipa baja API 5CT L80 dilengkapi dengan sambungan berulir dan berpasangan, tersedia dalam ujung polos, ulir bulat tanpa atau dengan kopling, benang penopang dengan atau tanpa kopling, dll. Kisaran ukurannya adalah 114,35.21-50816,13 mm, termasuk jenis benang seperti BTC, LTC, STC, dll. Komposisi kimianya memerlukan kandungan sulfur dan fosfor masing-masing kurang dari 0,030%, dan harus lulus uji perataan, uji tarik, dan uji hidrostatis. Cacat seperti lipatan dan retakan tidak diperbolehkan pada permukaan bagian dalam dan luar casing. Ujung berulir dilengkapi dengan pelindung, dan perawatan permukaan mengadopsi proses pengecatan semprot.
Spesifikasi
|
Nama Produk |
CASING & TABUNG |
|
Koneksi |
Digunakan untuk pengiriman cairan bertekanan rendah, seperti air, gas, dan minyak. Pengeboran minyak dan pembuatan mesin, dll. |
|
Produk |
Tabung API 5CT |
|
Diameter |
1.9" - 4-1/2" |
|
Kelas Baja |
J55/ K55, N80-1, N80Q, L80,C90, T95, P110 |
|
Berakhir |
PE, STC, LTC, BTC, EU,IEU, VAM,VAM Top, VAM Baru |
|
Produk |
Casing API 5CT |
|
Diameter |
4-1/2" -20" |
|
Kelas Baja |
J55/ K55, N80-1, N80Q, L80,C90, T95, P110 |
|
Berakhir |
PE, STC, LTC, BTC, EU,IEU, VAM,VAM Top, VAM Baru |
|
Produk |
Pipa Bor API 5DP |
|
Diameter |
2-3/8" - 6-5/8" |
|
Kelas Baja |
E75, X95, G105, S135 |
Standar Komposisi Pipa Casing API-5CT L80
| Nilai | C Kurang dari atau sama dengan | Si Kurang dari atau sama dengan | Mn Kurang dari atau sama dengan | P Kurang dari atau sama dengan | S Kurang dari atau sama dengan | Cr Kurang dari atau sama dengan | Ni Kurang dari atau sama dengan | Cu Kurang dari atau sama dengan | Juga Kurang dari atau sama dengan |
| API 5CT L80 | 0.15-0.22 | 1.00 | 0.25-1.00 | 0.020 | 0.010 | 12.0-14.0 | 0.20 | 0.20 | 0.020 |
API Baja Karbon 5CT GR. Analisis Mekanik Pipa L80
| Kelas Baja | Kekuatan Hasil (Mpa) | Kekuatan Tarik (Mpa) |
| API 5CT L80 | 552-655 | Lebih besar atau sama dengan 655 |
Toleransi Dimensi Pipa API 5CT GR.L80
| Jenis tabung baja | Diameter Luar | Ketebalan Dinding | |
| Tabung canai-dingin | Ukuran tabung (mm) | Toleransi (mm) | Toleransi (mm) |
| ＜114.3 | ±0.79 | －12.5％ | |
Dimensi Pipa Saluran Baja Karbon API 5CT L80
| Ukuran | Berat | Diameter Luar | Ketebalan Dinding | Akhir Selesai | ||||||
| Nilai | ||||||||||
| di dalam | mm | di dalam | mm | J55K55 | L80 | N80 | C90T95 | P110 | ||
| 4 1/2 | 9.50 | 4.500 | 114.3 | 0.205 | 5.21 | PS | – | – | – | – |
| 10.50 | 0.224 | 5.69 | PSB | – | – | – | – | |||
| 11.60 | 0.250 | 6.35 | PSLB | PLB | PLB | PLB | PLB | |||
| 13.50 | 0.290 | 7.37 | – | PLB | PLB | PLB | PLB | |||
| 15.10 | 0.337 | 9.56 | – | – | – | – | PLB | |||
| 5 | 11.50 | 5.00 | 127.00 | 0.220 | 5.59 | PS | – | – | – | – |
| 13.00 | 0.253 | 6.43 | PSLB | – | – | – | – | |||
| 15.00 | 0.296 | 7.52 | PSLB | PLB | PLB | PLBE | PLB | |||
| 18.00 | 0.362 | 9.19 | – | PLB | PLB | PLBE | PLB | |||
| 21.40 | 0.437 | 11.10 | – | PLB | PLB | PLB | PLB | |||
| 23.20 | 0.478 | 12.14 | – | PLB | ||||||
| 24.10 | 0.500 | 12.70 | – | PLB | ||||||
| 5 1/2 | 14.00 | 5.500 | 139.7 | 0.244 | 6.20 | PS | – | – | – | – |
| 15.50 | 0.275 | 6.98 | PSLB | – | – | – | – | |||
| 17.00 | 0.304 | 7.72 | PSLB | PLB | PLB | PLBE | PLB | |||
| 20.00 | 0.361 | 9.17 | – | PLB | PLB | PLBE | PLB | |||
| 23.00 | 0.415 | 10.54 | – | PLB | PLB | PLBE | PLB | |||
| 6 5/8 | 20.00 | 6.625 | 168.28 | 0.288 | 7.32 | PSLB | – | – | – | – |
| 24.00 | 0.352 | 8.94 | PSLB | PLB | PLB | PLBE | PLB | |||
| 28.00 | 0.417 | 10.59 | – | PLB | PLB | PLBE | PLB | |||
| 32.00 | 0.475 | 12.06 | – | PLB | PLB | PLBE | PLB | |||
| 7 | 17.00 | 7.00 | 177.80 | 0.231 | 5.87 | – | – | – | – | – |
| 20.00 | 0.272 | 6.91 | PS | – | – | – | – | |||
| 23.00 | 0.317 | 8.05 | PSLB | PLB | PLB | PLBE | – | |||
| 26.00 | 0.362 | 9.19 | PSLB | PLB | PLB | PLBE | PLB | |||
| 29.00 | 0.408 | 10.36 | – | PLB | PLB | PLBE | PLB | |||
| 32.00 | 0.453 | 11.51 | – | PLB | PLB | PLBE | PLB | |||
| 35.00 | 0.498 | 12.65 | – | PLB | PLB | PLBE | PLB | |||
| 38.00 | 0.540 | 13.72 | – | PLB | PLB | PLBE | PLB | |||
| 7 5/8 | 24.00 | 7.625 | 193.68 | 0.300 | 7.62 | – | – | – | – | – |
| 26.40 | 0.328 | 8.33 | PSLB | PLB | PLB | PLBE | PLB | |||
| 29.70 | 0.375 | 9.52 | – | PLB | PLB | PLBE | PLB | |||
| 33.70 | 0.430 | 10.92 | – | PLB | PLB | PLBE | PLB | |||
| 39.00 | 0.500 | 12.70 | – | PLB | PLB | PLBE | PLB | |||
| 42.80 | 0.562 | 14.27 | – | PLB | PLB | PLB | PLB | |||
| 45.30 | 0.595 | 15.11 | – | PLB | PLB | PLB | PLB | |||
| 47.10 | 0.625 | 15.88 | – | PLB | PLB | PLB | PLB | |||
| 8 5/8 | 24.00 | 8.625 | 219.08 | 0.264 | 6.71 | PS | – | – | – | – |
| 28.00 | 0.304 | 7.72 | – | – | – | – | – | |||
| 32.00 | 0.352 | 8.94 | PSLB | – | – | – | – | |||
| 36.00 | 0.400 | 10.16 | PSLB | PLB | PLB | PLBE | PLB | |||
| 40.00 | 0.450 | 11.43 | – | PLB | PLB | PLBE | PLB | |||
| 44.00 | 0.500 | 12.70 | – | PLB | PLB | PLBE | PLB | |||
| 49.00 | 0.557 | 14.15 | – | PLB | PLB | PLBE | PLB | |||
| 9 5/8 | 32.30 | 9.625 | 244.48 | 0.312 | 7.92 | – | – | – | – | – |
| 36.00 | 0.352 | 8.94 | PSLB | – | – | – | – | |||
| 40.00 | 0.395 | 10.03 | PSLB | PLB | PLB | PLBE | – | |||
| 43.50 | 0.435 | 11.05 | – | PLB | PLB | PLBE | PLB | |||
| 47.00 | 0.472 | 11.99 | – | PLB | PLB | PLBE | PLB | |||
| 53.50 | 0.545 | 13.84 | – | PLB | PLB | PLBE | PLB | |||
| 58.40 | 0.595 | 15.11 | – | PLB | PLB | PLB | PLB | |||
| 10 3/4 | 32.75 | 10.75 | 273.05 | 0.279 | 7.09 | – | – | – | – | – |
| 40.50 | 0.350 | 8.89 | PSB | – | – | – | – | |||
| 15.50 | 0.400 | 10.16 | PSB | – | – | – | – | |||
| 51.00 | 0.450 | 11.43 | PSB | PSB | PSB | PSBE | PSB | |||
| 55.50 | 0.495 | 12.57 | – | PSB | PSB | PSBE | PSB | |||
| 60.70 | 0.545 | 13.84 | – | – | – | PSBE | PSB | |||
| 65.70 | 0.595 | 15.11 | – | – | – | PSB | PSB | |||
| 13 3/8 | 48.00 | 13.375 | 339.73 | 0.330 | 8.38 | – | – | – | – | – |
| 54.50 | 0.380 | 9.65 | PSB | – | – | – | – | |||
| 61.00 | 0.430 | 10.92 | PSB | – | – | – | – | |||
| 68.00 | 0.480 | 12.19 | PSB | PSB | PSB | PSB | PSB | |||
| 72.00 | 0.514 | 13.06 | – | PSB | PSB | PSB | PSB | |||
| 16 | 65.00 | 16 | 406.40 | 0.375 | 9.53 | – | – | – | – | – |
| 75.00 | 0.438 | 11.13 | PSB | – | – | – | – | |||
| 84.00 | 0.495 | 12.57 | PSB | – | – | – | – | |||
| 109.00 | 0.656 | 16.66 | P | P | P | – | P | |||
| 18 5/8 | 87.50 | 18.625 | 473.08 | 0.435 | 11.05 | PSB | – | – | – | – |
| 20 | 94.00 | 20 | 508.00 | 0.438 | 11.13 | PSLB | – | – | – | – |
| 106.50 | 0.500 | 12.70 | PSLB | – | – | – | – | |||
| 133.00 | 0.635 | 16.13 | PSLB | – | – | – | – | |||
Proses pembuatan produk
